Installation
[SEE-U] Where to install the varistors in the SEE-U kit ref 1391
The SEE-U kit ref. 1391 includes a small bag containing 2 varistors. The main function of these varistors is to prevent reverse currents caused by the door release coil, which can lead to malfunctions and damage in the outdoor panels. 12V DC door ...
Is it possible that the key of my NON-WIFI monitor opens the gate instead of the door opening connected in +s-s?
Yes, as the main monitor allows the Exit button to be configured to activate one or the other output. Opening selection: Enabling the Exit button (Exit on the back of the board). We can select whether pressing this button activates the door opening ...
What accessory do I need if my door has a bolt entry and the opener I have has a short armature?
The mortise lock shown in the drawing has a key entry, so the lock release must have a long armature as shown in the drawing. For this purpose, as our lock release has a short armature Replace the short armour with the long armour. Order the long ...
Which door release can I connect to the see-u kit?
The electric lock release must be of low consumption direct current, less than 250mA Fermax recommends ref. 29588 DOOR OPENER 300N-412-S if the grille or entrance door has a bolt entry, you must change the trim plate of the electric lock release and ...
Can I use the existing door opener from my old door entry system to connect it to the see-u kit?
f the electric lock release that you had installed when opening the door sounded like a buzzer, it means that it is an AC electric lock release (12Vac/ac), so you cannot use the +s-s output connections directly to the electric lock release, but you ...
What happens if my electric lock release consumes more than 250mA? Can I connect it to the outdoor panel?
Yes, but using an independent power supply that you will have to buy, for example if it is a 12Vdc, ref. 4813, and using the potential-free relay contact on the panel. The diagram would be as follows. Switch JP1 must be set to NO (normally open). If ...
Once I have made the expansions, how do I enable the devices on my NON WIFI 1392 monitor so that I can view them and auto power on?
Being in my monitor NO WIFI SEE-U ref. 1392 the access buttons are on the outside of the monitor and correspond with the symbology that is represented on the screen. Entering in configuration 1ยบ We move with the symbol of the gate until we get to ...
How do I set up an additional monitor?
The monitor must be configured as EXT. 1, 2 or 3 (see instructions for see-u WIFI or NO WIFI monitor) and the last monitor installed in terms of wiring, the one furthest away from the outdoor panel, will have to have a jumper on the back configured ...
Can I combine both WIFI and NON-WIFI monitors in my SEE-U KIT?
Yes, but only one will be the master and if there is a monitor or several WIFI monitors, only the WIFI monitor that is connected to the home's wifi will be the master. The rest of the monitors will be configured as EXT1, EXT2 or EXT3, even if they ...
What is the purpose of the doorbell, which allows me to connect my NON-WIFI monitor?
The doorbell consists of two wires (BELL, GND) that would go to the push button at the entrance to the home itself so that the monitor plays a different bell if called from the outdoor panel or from the doorbell itself, so we know that the visitor ...
What is the purpose of the doorbell, which allows my monitor to be connected?
The doorbell has two wires (BELL, GND) that go to the entrance button to the home itself so that the monitor plays a different bell if it is called from the outdoor panel or from the doorbell of the home itself, so that we know that the visitor has ...
Which power supply does this kit use?
The power supply that powers the monitor connected directly to the board is the one that powers the outdoor panel. The reference of the monitor power supply is ref. 1390.
How do I adjust the audio of the see-u board, both the loudspeaker and microphone volume of the see-u board?
By means of the 2 blue potentiometers on the back of the outdoor panel itself we can adjust. Both the volume of the outdoor panel speaker and the microphone of the outdoor panel.
How do I know if my SEE-U ref. 1392 NO WIFI monitor is on or off?
On the top right hand side of the NO WIFI monitors ref. 1392, we have the power on LED indicator. If the monitor is on, it is indicated by the fixed illuminated LED. .
Why doesn't my 1394 monitor ring when it receives a board call?
In installations with only one monitor in the kit, we recommend checking the configuration of the monitor as it should be configured as MASTER. Also, check the MUTE indicator if it is active the LED indicates that it has been muted. To re-activate ...
Why doesn't my 1392 NO WIFI monitor ring when it receives a badge call?
In installations with only one monitor in the kit, we recommend checking the configuration of the monitor as it should be configured as MAIN. Also, check the MUTE indicator if it is active, the LED indicates that it has been muted. To activate it ...
How do I factory reset my SEE-U 1392 NO WIFI monitor?
Factory Reset: This option allows us to reset the monitor to the initial values. When we select it, we are prompted for a second confirmation if we want to execute it. So we will press the eye to confirm.
Can I open the gate from a secondary NON-WIFI monitor?
Yes, all monitors have both the key and the gate icon to open an auxiliary gate.
How do I set the outdoor panel output button to activate the gate (auxiliary relay output) instead of the pedestrian door (+S-S output)?
Accessing from the MAIN monitor to the main menu You must access the main menu by pressing the touch screen and then slide the screen to the left until you see the following menu We will press on Direction where we will go to the next menu where we ...
How do I set my see-u wifi 1394 monitor as master or secondary?
You must access the main menu by pressing the touch screen and then swiping the screen to the left until you see the following menu Press on Address to go to the following menu Where we will indicate if it is the main one or a secondary one and which ...
How do I add an additional monitor or board to my see-u kit?
Below you can see how we would add an additional monitor or board. It is allowed to have with the kit up to 4 cascaded monitors including the one in the kit. The intermediate monitors will be configured like this and will be configured in the ...